AXAGON 2.5/3.5 ADSA-ST

AXAGON ADSA-ST USB3.0 - 2x SATA 6G CLONE DUAL HDD Dock Station

AXAGON ADSA-ST USB 3.0 docking station connects to your computer easily and quickly any SATA drive or even two drives at one time.

A handy helper for the easiest and fastest way to connect any SATA drive to your computer - just plug the drive into the base.

SATA 6G interface with UASP support allows you to enjoy the speed of modern SSD drives.

Easy and fast cloning of the contents of attached drives without the need for a PC connection.

HDD dock can be used as an autonomous device for comfortable disk image creation.

SSD cloning speed up to 300 MB/s.

Reading of S. M. A. R. T. information monitoring the condition of the connected drives.

Supports spinning down of attached drives and stations.

Automatic installation can be handled even by a layman.

Durable and robust case design for perfect stability.

Rubber feet to reduce vibrations.

Outer casing made of aluminum with elegant brushed finish.

Features:
Compatible with USB 3.0 and backward compatible with USB 2.0.
Supports transmission rates 12 / 480 / 5000 Mb/s (low / full / high speed).
Supports 2.5 "and 3.5" SATA III / II / I drives of all capacities.
Compliant with Serial ATA 3.1 specification (SATA/600), transmission rates of up to 6 Gb/s.
Compliant with Serial ATA 2.0 specification (SATA/300), transmission rates of up to 3 Gb/s (300 MB/s).
Compliant with Serial ATA 1.0 specification (SATA/150), transmission rates of up to 1.5 Gb/s (150 MB/s).
The total bandwidth / transmission rate of the station is determined by the USB 3.0 interface used (theor. 5 Gbit/s).
Supports UASP (USB Attached SCSI Protocol) and BOT (Bulk-Only Transport).
SSD/HDD boot support in docking station.
Possibility to connect your device while running thanks to the Hot Plug support.
Full Plug and Play support.
HDD Auto Spindown - automatic spinning down after period of inactivity lasting 10 minutes.
HDD Turn Off - turns off the drive after removing the device or spinning down the PC.
Connection via durable large USB 3.0 Type B female connector.
USB 3.0 cable USB 3.0 Type A male / USB 3.0 Type B male 70 cm long is included.
3 LEDs indicating power to the HDD dock and activity of disks in both shafts.
Power switch.
Power supply via a compact external AC/DC adapter 12 V - 2.5 A (30 W) with a 150 cm long supply cable.
Station dimensions 142 x 102 x 80 mm.
Weight 330 g.

Feature of disk contents cloning:
Cloning takes place without connecting the station to a computer.
The target disk must have the same or larger capacity as the source disk, otherwise cloning cannot be started.
Both hard disks and SSDs can be cloned.
Cloning starts by pressing and holding the CLONE button for minimally 3 seconds.
Four LEDs indicate the progress and completion of cloning.
SSD cloning speed up to 300 MB/s.
The total disk cloning time depends on the capacity of the source disk, not the amount of disk data.

Supported OSs: MS Windows XP / Vista / 7 / 8 / 8.1 / 10 and later, Windows Server 2003 / 2008 / 2012 / 2016 and later (supported are all 32- and 64-bit Windows OS versions), Mac OS X 10. x and higher, Linux with kernel 2.6. x and above.
Note: Drivers are included with supported operating systems and are installed completely automatically. No other drivers need to be installed and are not even available.